XStream"燨EM燫F燤odule?燩roduct燤anual爒5.x00燵2006.02.24]?/DIV>
FH (Force Wake-up Initializer) Command
AT Command: ATFH
Binary Command: 0x0D (13 decimal)
<Sleep (Low Power)> FH Command is used to
force a Wake-up Initializer to be sent on the next
transmission. WR (Write) Command does not
need to be issued with FH Command.
Use only with cyclic sleep modes active on remote modules.
FL (Software Flow Control) Command
AT Command: ATFL
Binary Command: 0x07 (7 decimal)
Parameter Range: 0 1
Parameter
Configuration
0
Disable software
flow control
1
Enable software
flow control
Default Parameter Value: 0
Number of bytes returned: 1
<Serial Interfacing> FL Command is used to
configure of module with software flow control.
Hardware flow control is implemented with the
XStream Module as the DO2 pin (
), which
regulates when serial data can be transferred to
the module. FL Command is used to allow
software flow control. XON character used is
0x11 (17 decimal). XOFF character used is 0x13
(19 decimal).
FT (Flow Control Threshold) Command
AT Command: ATFT
Binary Command: 0x24 (36 decimal)
<Serial Interfacing> Set/Read the flow control
threshold. When FT bytes have accumulated in
the DI buffer,
is de-asserted or the XOFF
software flow control character is transmitted.
Parameter Range: 0 0xFF [bytes]
(Maximum value equals the receiving module
DO buffer size minus 0x11 bytes)
Default Parameter Value: Receiving module DO
Buffer size minus 0x11
Number of bytes returned: 2
Minimum Firmware Version Required: 4.27B
GD (Receive Good Count) Command
<Diagnostics> Set/Read the count of good
received RF packets. Parameter value is reset to
0 after every reset and is not non-volatile (value
does not persist in the modules memory after a
power-up sequence). Once the Receive Good
Count reaches its maximum value (up to
0xFFFF), it remains at its maximum count value
until the maximum count value is manually changed or the module is reset.
AT Command: ATGD
Binary Command: 0x10 (16 decimal)
Parameter Range: 0 0xFFFF
Default Parameter Value: 0
Number of bytes returned: 2
Related Commands: ER (Receive Error Count)
HP (Hopping Channel) Command
<Networking & Security> HP Command is used
to set the module hopping channel number. A
channel is one of three layers of addressing
available to the module. In order for modules to
communicate with each other, the modules must
have the same channel number since each
network uses a different hopping sequence.
Different channels can be used to prevent
modules in one network from listening to transmissions of another.
AT Command: ATHP
Binary Command: 0x11 (17 decimal)
Parameter Range: 0 6
Default Parameter Value: 0
Number of bytes returned: 1
Related Commands: DT (Destination Address),
ID (Module VID), MK (Address Mask)
牋牘?006燤axStream,營nc.燙onfidential燼nd燩roprietary?/DIV>
25?/DIV>
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
XIB-R
BOARD INTERFACE RS232/485
ZMN2400HPDB
BOARD ROUTER DEV ZIGBEE 100MW
ZMN24HPDK-B
KIT DEV W/ZIGBEE ZMN2400HP
ZNI1000TC
IC TEMP SENSOR NI1000 SOT23-3
02110102-000
SNSR TILT RATIO 60DEG 500MA FLNG
1-5209285-2
FOPC BOA 12DB FC/UPC BP SM
2-1693560-0
BOA 20DB LC/UPC BB
517SS16
MAGNETIC SENSORS BIPOLAR ICS
相关代理商/技术参数
XIB-R
功能描述:界面模块 RS-232/485 interface 24XStream 9XCite
RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度:
XIB-U
功能描述:界面模块 USB interface board 24XStream 9XCite
RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度:
XIC25040
制造商:XIC 功能描述:25040 24HR '6
XILINXPWR-079
功能描述:电源管理IC开发工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
XILINXPWR-080
功能描述:电源管理IC开发工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
XILINXPWR-081
功能描述:电源管理IC开发工具 Pwr Mgmt Eval Mod Xilinx RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
XILINXPWR-082
功能描述:电源管理IC开发工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
XILINXPWR-083
功能描述:电源管理IC开发工具 Pwr Mgmt Eval Mod Xilinx RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V